How To Remove a Sensor From ADT System

There are different methods you can use to remove your widow and door sensor from your ADT system. If you are looking to remove the sensor from your ADT system, you should know that there are some preliminary steps you need to take before removing the steps. Below is a list of the steps you need to take.

Step 1: Go to the ADT Command Network

This is the first thing you need to do once you are looking to remove the sensor from your ADT system. The command network gives you access to turn on and turn off different security devices in your house.

Step 2: Select Zone

This is the next thing you need to do once you have gone to the command zone. You still need to click on the select zone. The select zone options give you the freedom to access different security devices in different zones in the house.

Step 3: Bypass and Enter the User Code

Once you have clicked on <select zone>, you can move on to click on bypass zone. By clicking on bypass zone, you automatically turn off or deactivate the security system in the select zone you intend to deactivate.

If you want to deactivate the sensor on your ADT system, select the zone where the sensor is located and bypass it. Once this is done, you are good to remove the sensor from the ADT system.

Apart from using this method to turn off your sensor, there is also another method you can use to bypass the zone in your house. If you are looking to bypass the zone, all you need to do is upgrade the software on your device. Once you do, you will get access to all the zones instantly which means, you will be able to bypass the zones easily.

You can also go to the website to bypass the zone on your ADT system. If you are looking to bypass the zone, you can easily go to the control panel with your user code. Once you do this, you will need your number followed by the 3 digits zone number. The zone should automatically get bypassed once this is done.

Do this for the zone where your door or window sensor is located and you will be set to remove the sensors without making an alarm or disturbance.

Once you have done this, you can then proceed to remove the sensor from your ADT system. As said earlier, there are different methods you can use to remove the sensor located at different parts of your house. Below is a list of methods for the different types of ADT sensors you use in your house.

Removing the Window and Door Wireless Sensor from your ADT System

It is a relatively easy process to remove your window and door sensor from your ADT system. If your door sensor is wireless, you should know that a bead of glue was most likely used during the installation process.

If this is so, you should probably get a knife or razor. It has to be relatively sharp so it will work efficiently. Once you get this tool, you can easily cut through the silicone lining around your sensor.

Ensure you carefully do this so you do not ruin the sensor. Carefully cut through the glue around the sensor and remove the sensor. This is one method you can use from your wireless sensor.

If you don’t want to do this, you can easily use a hot air gun to weaken the adhesive. Once the adhesive is removed, you can then move on to pull out the sensor. You can also use an adhesive or glue removal.

Different chemicals help to remove adhesive. Once you do this, the adhesive should be removed and your wireless door sensor is set to be removed.

How to Remove Wired Door or Window Sensor from Your ADT System

While removing a wired sensor from your ADT system is relatively easy, you should it is something you should do with care. This is because the sensor is wired and you wouldn’t want to ruin the wires in case you would like to install the sensor sometime in the future.

The process of removing a wired sensor is different from the process you use to read your wireless sensor. You need to pay extra attention when removing a wired sensor.

The first thing you need to do when removing your wired window or door sensor from your ADT system is to look for where the wires are located.

Once you do this, you can then pull out the wires through the wall. I mentioned walls here because it is the likely place where your wires will pass through. If it is underground, you can still pull the wires from where it passed through.

After pulling the wires, you will have to take your time to use a screwdriver to unscrew the wires at the two ends of the connections.

That is, you will have to unscrew the wires connected to the end of the sensor and the control panel. Once you have done this, you can easily keep the wires somewhere safe so you will be able to use them for future purposes.

How to Remove Recessed Doors and Window Sensor from your ADT System

Removing a recessed door sensor can be a little complicated. This is because it isn’t as easily accessible as removing a wired or wireless door and window sensor.

When removing a recessed door or window sensor, you will have to get your screwdriver ready.

This is because door and window censored are usually built or kept within the frame, it can be a little hard to remove them.

When removing this type of sensor, you will have to take your time to use your fingers or your screwdriver to look for the magnet in your sensor within the frame.

Once you can touch the magnet, you can move ahead and remove the magnet. Remove the wires and every other thing once the magnet is removed.

With this method, you have successfully removed your recessed door and window sensor from your ADT system.

Why is My ADT System not Working

It is a pretty frustrating thing to notice that your ADT system isn’t working. You might be wondering why your ADT system isn’t working. Below is a list of reasons why your ADT system isn’t working

Internet Connection

This is the first possible reason why your ADT system isn’t working. If there is a bad internet connection in your home, the chances of your ADT system working properly is pretty much low.

Internet connections affect the efficiency of devices that rely on the internet to function. Once you notice that the app int loading or the system isn’t responding the way it is supposed to, you should check the internet connection to make sure the signal strength and quality are okay.

Faulty Motion Sensor

The ADT system is supposed to notify you once someone comes within the zone you set. if it doesn’t notify you, there is a pretty big chance that the motion sensor of your ADT system isn’t in a good shape.

Check the motion sensor to ensure it is working fine. If it isn’t, you might have to take your time to fix the motion sensor. Once you notice that the motion sensor cannot be fixed, you will probably have to change the motion sensor.

Power Problem

This is another reason why your ADT system might not be working properly. If any of your sensors is having power issues, it will not work or respond to commands.

You have to take time out to check if all the security accessories are well charged. If they aren’t, take your time to ensure charge them up properly. You can also change the flat batteries of the system. Your ADT sensor should begin to work once you do this.

Video Guide

Conclusion

There are different things you can do to remove a sensor from your ADT system. However, you need to know that there are some preliminary steps you must take before you remove the sensors. Once these steps which have been discussed in this article are taken, you can go ahead and remove the sensor.

You should also know that there are different reasons why your ADT system isn’t working. Read through this article and you will get solutions to your ADT system problems.

Source

https://help.adt.com/s/article/Troubleshooting-FAQs